Frame Legs for Slate Frames (IGG)

  • Sale
  • $ 32.50 USD
  • Regular price $ 65.00 USD

These beautiful feet are made from European Beech and Purpleheart. They can be pinned through the adjustment holes on the side bars of your frame, or attached with elastic bands anywhere along the side bar. The "Short" feet have 100mm/4" of clearance below the frame, the "Long" feet have 150mm/6" below the frame. With four feet attached to your frame, the frame will sit parallel to your work surface which is perfect for certain types of embroidery.

We wanted to ensure these feet would be strong and cope with falling off a table without breaking. As the slot for the side bar is cut into the grain direction of the foot, we reinforce the slot with a laminated piece of Purpleheart (which we think looks gorgeous!) - making the top section of the foot like plywood.

Each foot has a hole in the top that aligns with the outer most holes on the frame bar, allowing you to lock the foot every 10mm where the holes are. There's just enough room in the slot to allow you to attach the feet over lacing.

 

Name/Message Engraving

To have a name or message engraved on this frame, please select the "Name or Message" option. Typically we use the "Great Vibes" font for engravings, other calligraphic fonts we have tried tend to have a poor "s" character in both capitals and lower case. You're welcome to specify any "free for commercial use" font you wish, however keep in mind that bolder fonts show up a lot better than narrower fonts. Font Squirrel is a great place to look at fonts, as all of them are free!

Logo/Graphic Engraving

You can also have a logo, picture or even full width artwork engraved by selecting the logo option for engraving, I'll work with you after the purchase to ensure your artwork is suitable. Any greyscale image or black and white image can be engraved. Keep in mind that the total height of the engraving is a maximum of about 18mm (just less than 3/4") - that being said, we can engrave a huge amount of detail in that height very accurately.

All holes are precision drilled with a computer controlled drill which ensures the frame will not be lopsided, and that the holes are exactly the same distance apart on both ends. The mortises for the side bars to fit through are also precision machined with just enough tolerance to allow for finish thickness, and the expansion of the wood at different humidity and temperature.

Tight fitting steel cotter pins are used rather than wooden dowels. These last much longer, are easier to find replacements for if you lose one, and are much less likely to fall out. The pins fit within the holes on the side bars snugly, so they will not fall out or vibrate loose during travel or long term storage. Each pin is hand ground so it's less likely to scratch your work surface or catch threads/fabric.

To protect the wood, several coats of Danish Oil are allowed to soak into and cure in the wood, which stabilises the wood and makes it much tougher to resist dents and marking as well as visually bringing out the grain. The danish oil cures for several weeks to ensure it is fully hardened. Next several coats of extremely hard urethane gloss coating is applied, typically used for high traffic outdoor wood floors. This coating prevents any oils on your hands, moisture or dirt from making its way into the wood and being transferred onto your fabric, as well as preventing discolouration/damage of the wood from UV light if the frame is left near a window. The danish oil and urethane coatings are applied in an industrial paint spray booth to greatly reduce the amount of dust and other particles trapped in the finishes.

These frames are made and finished to retain their quality through generations.

In short, your fabric must be narrower than the Working Area Width of the frame, usually by at least 30mm (1 ¼"). Your fabric can be longer than the length, however, if you're working with fragile threads (eg: Goldwork), beads (eg: Couture), or raised work (eg: Stumpwork) your project should fit within the maximum length.

All of our frames list their "working area" in the description, here's a direct comparison. The width is considered between the two Side (Stretcher) Bars and the length between the Top/Bottom (Roller) Bars.

Frame Size
(class)

Width
mm (inches)

Length
mm (inches)

250mm (std)170mm
(6.69")
84-194mm
(3.31-7.64")
300mm (std)218mm
(8.58")
100-230mm
(3.93-9.05")
350mm (std)268mm
(10.55")
100-280mm 
(3.93-11.02")
400mm (std)318mm
(12.51")
100-330mm 
(3.93-12.99")
450mm (std)368mm
(14.48")
100-380mm 
(3.93-14.96")
500mm (std)418mm
(16.45")
140-430mm
(5.51-16-92")
550mm (std)468mm
(18.42")
180-470mm
(7.08-18.50")
600mm (large)520mm
(20.47")
224-514mm
(8.82-20.24")
700mm (large)610mm
(24.02")
314-604mm
(12.36-23.78")
850mm (large)770mm
(30.31")
474-764mm
(18.66-30.08")

For the full guide, please see our page Selecting the right size frame for your project.

Postage is automatically calculated at checkout once your address is entered.

We offer shipping via UPS (usually fastest and cheapest), Canada Post, Purolator (to Canada/USA), and DHL. You can select the service/rate you most prefer.

We have standard sized heavy duty boxes for all of our standard sized items, with enough space fo copious amounts of bubblewrap (never packing peanuts!)